Effect of Post Welding Heat Treatment on the Mechanical Properties of Welds of AISI 1040 Medium Carbon Steel

S K Fasogbon, A P Okediji, H A Owolabi

Abstract


AISI 1040 steel is one of the grades of medium carbon steel of American standard and as such, is mostly being used in the industries. Again, when welding a piece of material, only the joint and surrounding area being welded (Heat Affected Zone, HAZ) is heated and cooled. This causes uneven expansion and cooling, and the piece begins to warp or distort at the point. Uncontrolled Distortion may lead to a serious dimensional defect/failure. In order to arrest this failure, Steps may be taken before, during, and after welding to minimize or control the effects of this heat distortion. Controlling the effects of heat distortion after welding forms the basis of this study. To this end, this work studied the effects of post welding heat treatments on the mechanical properties of welds of AISI 1040 medium carbon steel. Butt-welds of AISI 1040 medium carbon steel were prepared with the aid of electric arc welding and subsequently subjected to annealing, normalizing, hardening and tempering heat treatment processes. Finally, the welds were subjected to impact, tensile and Rockwell hardness tests. The results show that tempering improves the toughness of the steel at the HAZ. Normalizing refines the grain structure and relieve the internal stress, Annealing increases the ductility and softens the steel at the HAZ. Hardness and brittleness of the hardened and tempered pair increase while that of the normalized and annealed pair considerably reduced. The study recommends paired annealing and normalizing processes for welds of AISI 1040 medium carbon steel.

Full Text:

PDF

References


Adebayo, A. and Stephen, J.T. 2008. ‘Effect of heat treatment on the mechanical properties of mild steel’ Research Journal of Applied Sciences, Medwell Journals, 3(3) 162-166. Andersson, H. 2005. ‘Influence of weld micro structure on creep crack growth’ Unpublished M Sc thesis, Department of Material Science and Engineering, Division of corrosion science, Royal Institute of technology, Stockholm, Sweden. Lothongkum, G., Ratanamahasakul, S. and Wangyao, P. 2005). ‘Effect of heat treatment conditions on dynamic parameters of secondary carbide precipitation in centrifugally cast iron base superalloy’, Act a metallurgical slovaca. 11(1) 54-61

Mohandas, Srinivas and Kutumbarao 2001. ‘Effect of post weld heat treatment on fracture toughness and fatigue crack growth behavior of electron beam welds of a titanium alloy’ Fatigue and fracture resistance of engineering materials and structure, 23 (1) 33-38 Munsi, A.M.S.Y., Waddell, A.J. Walker C.A. 2001.‘The effect of vibratory stress on the welding micro structure and residual stress distribution’ Proceedings of the institution of mechanical engineers, Part L Journal of materials: Design and Applications, 215 (2) 99-111 Roy, S., Fisher, J.W. and Yen, B.T. 2003. ‘Fatigue resistance of welded details enhanced by ultrasonic impact treatment (UIT)’ International journal of fatigue, 25 (9-11) 1239-1247 Spitsen, R., Kim, D., Flinn, D., Ramulu, M. and Easterbrook, E.T 2005. ‘The effect of post weld cold working processes on the fatigue strength of low carbon steel resistance spot weld’. 127 (4718) 6 Tottens, E. and Howes, S. 1997. Physical metallurgy, 3rd ed. Prentice Hall, London. Treatment of welded structure’, http://www.wtia.com.au Retrieved on February 2013. Umoru, L.E. 2008. ‘Effect of weld type and post welding heat treatment on the corrosion resistance of AISI321 stainless steel in a tar sand digester’, Emirates journal of engineering research, 13(2) 4550 Welding Technology Institute of Australia (WTIA), 2003. Guidance Note 6, ‘Post weld heat treatment